Kontron AT8404 CLI Manual do Utilizador Página 246
- Página / 373
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Utility Commands AT8404
AT8404 CLI Reference Manual Page 4 - 32
4.7 Simple Network Time Protocol (SNTP) Commands
This section describes the commands you use to automatically configure the system time and date by using SNTP.
4.7.1 sntp broadcast client poll-interval
This command sets the poll interval for SNTP broadcast clients in seconds as a power of two where <poll-
interval> can be a value from 6 to 16.
4.7.1.1 no sntp broadcast client poll-interval
This command resets the poll interval for SNTP broadcast client back to the default value.
4.7.2 sntp client mode
This command enables Simple Network Time Protocol (SNTP) client mode and may set the mode to either
broadcast or unicast.
4.7.2.1 no sntp client mode
This command disables Simple Network Time Protocol (SNTP) client mode.
4.7.3 sntp client port
This command sets the SNTP client port id to a value from 1-65535.
4.7.3.1 no sntp client port
This command resets the SNTP client port back to its default value.
Default 6
Format sntp broadcast client poll-interval <poll-interval>
Mode Global Config
Format no sntp broadcast client poll-interval
Mode Global Config
Default disabled
Format sntp client mode [broadcast | unicast]
Mode Global Config
Format no sntp client mode
Mode Global Config
Default 123
Format sntp client port <portid>
Mode Global Config
Format no sntp client port
- AT8404 CLI Reference Manual 1
- AdvancedTCA 1
- Revision History 2
- Disclaimer 2
- AT8404 Preface 3
- About This Book 3
- Proprietary Note 3
- Trademarks 3
- Preface AT8404 4
- Explanation of Symbols 4
- For Your Safety 4
- Two Year Warranty 5
- Appendix 25
- 1.1 Command Syntax 28
- 1.2 Command Conventions 28
- 1.3 Common Parameter Values 29
- 1.6 FASTPATH Modules 30
- 1.7 Command Modes 31
- 1.9 CLI Error Messages 33
- 1.11 Using CLI Help 34
- 1.12 Accessing the CLI 34
- Switching Commands 37
- 2. Switching Commands 38
- Switching Commands AT8404 100
- AT8404 Switching Commands 101
- Quality of Service Commands 175
- Chapter 1 175
- -mapping 176
- 3.1.3 classofservice trust 177
- 3.1.4 cos-queue min-bandwidth 177
- 3.1.13 show packet-memory 180
- 3.1.16 show protection-group 181
- Mode Global Config 183
- 3.3.1 class-map 184
- 3.3.1.1 no class-map 184
- 3.3.2 class-map rename 184
- 3.3.3 match ethertype 184
- 3.3.4 match any 185
- 3.3.5 match class-map 185
- 3.3.5.1 no match class-map 186
- 3.3.6 match cos 186
- 3.3.7 match secondary-cos 186
- 3.3.9 match dstip 187
- 3.3.10 match dstip6 187
- 3.3.11 match dstl4port 187
- 3.3.12 match ip dscp 187
- 3.3.13 match ip precedence 188
- 3.3.14 match ip tos 188
- 3.3.15 match protocol 189
- 3.3.17 match srcip 189
- 3.3.18 match srcip6 190
- 3.3.19 match srcl4port 190
- 3.3.20 match vlan 190
- 3.3.21 match secondary-vlan 190
- 3.4 DiffServ Policy Commands 191
- 3.4.4 redirect 192
- 3.4.5 conform-color 192
- 3.4.6 class 192
- 3.4.6.1 no class 193
- 3.4.7 mark cos 193
- 3.4.8 mark ip-precedence 193
- 3.4.9 police-simple 194
- 3.4.10 policy-map 194
- 3.4.10.1 no policy-map 194
- 3.5 DiffServ Service Commands 195
- 3.6 DiffServ Show Commands 196
- Mode Privileged EXEC 197
- <slot/port> in 199
- 3.6.7 show service-policy 200
- 3.7.4 mac access-group 203
- 3.7.4.1 no mac access-group 203
- 3.7.5 show mac access-lists 203
- 3.8.1 access-list 204
- 3.8.1.1 no access-list 205
- 3.8.2 ip access-list 205
- 3.8.2.1 no ip access-list 206
- 3.8.3 ip access-list rename 206
- 3.8.5 ip access-group 207
- 3.8.5.1 no ip access-group 207
- 3.8.6 acl-trapflags 207
- 3.8.6.1 no acl-trapflags 207
- 3.8.7 show acl-traptimer 208
- 3.8.8 acl-traptimer 208
- 3.8.8.1 no acl-traptimer 208
- 3.8.9 show ip access-lists 208
- 3.8.10 show access-lists 209
- 3.9.1 ipv6 access-list 209
- 3.9.1.1 no ipv6 access-list 210
- 3.9.2 ipv6 access-list rename 210
- 3.9.3 {deny 210
- 3.9.4 ipv6 traffic-filter 211
- 3.9.5 show ipv6 access-lists 211
- 3.10.1 auto-voip all 212
- 3.10.1.1 no auto-voip all 212
- 3.10.2 auto-voip 213
- 3.10.2.1 no auto-voip 213
- 3.10.3 show auto-voip 213
- Utility Commands 215
- 4. Utility Commands 216
- AT8404 Utility Commands 217
- Utility Commands AT8404 218
- Management Commands 277
- 5. Management Commands 278
- AT8404 Management Commands 279
- Management Commands AT8404 280
- Getting Help 329
- A. Getting Help 330
- AT8404 Getting Help 331
- FASTPATH log messages 334
- B. FASTPATH Log Messages 335
- AT8404 FASTPATH log messages 336
- FASTPATH log messages AT8404 337
- List of Commands 350
- C. List of Commands 351
- .......3 - 9 352
- List of Commands AT8404 353
- AT8404 List of Commands 354
Manuais e produtos relacionados com Hardware Kontron AT8404 CLI
Hardware Kontron RTM8050 Manual do Utilizador
(37 páginas)
(37 páginas)
Hardware Kontron AT8050 Manual do Utilizador
(165 páginas)
(165 páginas)
Hardware Kontron RTM8242 Manual do Utilizador
(34 páginas)
(34 páginas)
Hardware Kontron AT8242 Manual do Utilizador
(109 páginas)
(109 páginas)
Hardware Kontron AT8060 Manual do Utilizador
(160 páginas)
(160 páginas)
Hardware Kontron RTM806x Manual do Utilizador
(40 páginas)
(40 páginas)
Hardware Kontron KT965 Series Manual do Utilizador
(90 páginas)
(90 páginas)
Hardware Kontron KTGM45-mITX Manual do Utilizador
(101 páginas)
(101 páginas)
Hardware Kontron KTQ45-FLEX Manual do Utilizador
(92 páginas)
(92 páginas)
Hardware Kontron KTQM67-mITX Manual do Utilizador
(148 páginas)
(148 páginas)
Hardware Kontron KTQ67-FLEX Manual do Utilizador
(137 páginas)
(137 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais